China manufacturer Timken, Skfbearing, NSK, NTN, CZPT Bearing, Kbc CZPT Bearing, Auto/ Agricultural Machinery Ball Bearing 6001 6002 6003 6004 6201 6202 6203 6204zz 2RS C3 with high quality

Product Description

Timken, SKFBearing, NSK, NTN, CZPT Bearing, Kbc CZPT Bearing, Auto/ Agricultural Machinery Ball Bearing Zz 2RS C3

Feartures:                                        
1. Low density. As the rolling body density decreases, high-speed operation of its centrifugal load is also reduced, which can work at higher speed.                                        
2. Moderate elastic modulus. Elastic modulus is too large due to stress concentration and reduce the bearing capacity of the bushing.                                        
3. Thermal expansion coefficient is small. Reduce the sensitivity to temperature changes, so that the bearing operating temperature range is wider.                                        
4. High compressive strength. High compressive strength is the need for high stress for rolling bearings.                                        
5. High hardness and high toughness. These 2 properties combine to achieve better surface roughness; and can prevent external particles and shock damage.                                        
6. Good anti-rolling contact fatigue and has a peel failure mode.                                        
7. Special occasions should have high temperature, corrosion resistance and stability.                                        
                                        
Applications:                                        
The ceramic material has low density, medium elastic modulus, thermal expansion coefficient is small, high hardness, high temperature, corrosion resistance, non-magnetic, etc., to silicon nitride ceramic ball for the rolling body of ceramic ball bearings can significantly improve the bearing contact fatigue life, Has greatly expanded the application of rolling bearings, has been widely used in a variety of high-precision, high-speed machine tools, automobiles, racing, subway, motor, aero engine, petrochemical machinery, metallurgical machinery and other fields  
                                     
 

Bearing No. Boundary Dimensions(mm) Basic Load Rating (KN) Weight
Open Shields Seals d D B Cr. Cor. (Kg)
6000 6000-Z 6000-2Z 6000-RS 6000-2RS 10 26 8 4.58 1.98 0.02
6001 6001-Z 6001-2Z 6001-RS 6001-2RS 12 28 8 5.1 2.36 0.02
6002 6002-Z 6002-2Z 6002-RS 6002-2RS 15 32 9 5.6 2.85 0.033
6003 6003-Z 6003-2Z 6003-RS 6003-2RS 17 35 10 6 3.25 0.04
6004 6004-Z 6004-2Z 6004-RS 6004-2RS 20 42 12 9.4 5 0.07
6005 6005-Z 6005-2Z 6005-RS 6005-2RS 25 47 12 10 5.85 0.083
6006 6006-Z 6006-2Z 6006-RS 6006-2RS 30 55 13 12.7 8 0.126
6007 6007-Z 6007-2Z 6007-RS 6007-2RS 35 62 14 16 10.2 0.163
6008 6008-Z 6008-2Z 6008-RS 6008-2RS 40 68 15 16.6 11.6 0.2
6009 6009-Z 6009-2Z 6009-RS 6009-2RS 45 75 16 20 14.3 0.253
6571 6571-Z 6571-2Z 6571-RS 6571-2RS 50 80 16 20.8 15.6 0.282
6011 6011-Z 6011-2Z 6011-RS 6011-2RS 55 90 18 28.5 21.2 0.409
6012 6012-Z 6012-2Z 6012-RS 6012-2RS 60 95 18 29 23.2 0.413
6013 6013-Z 6013-2Z 6013-RS 6013-2RS 65 100 18 30.5 25 0.464
6014 6014-Z 6014-2Z 6014-RS 6014-2RS 70 110 20 38 31 0.642
6015 6015-Z 6015-2Z 6015-RS 6015-2RS 75 115 20 39 33.5 0.676
6016 6016-Z 6016-2Z 6016-RS 6016-2RS 80 125 22 47.5 40 0.893
6201 6201-Z 6201-2Z 6201-RS 6201-2RS 12 32 10 6.8 3.05 0.039
6202 6202-Z 6202-2Z 6202-RS 6202-2RS 15 35 11 7.8 3.75 0.045
6203 6203-Z 6203-2Z 6203-RS 6203-2RS 17 40 12 9.58 4.78 0.064
6204 6204-Z 6204-2Z 6204-RS 6204-2RS 20 47 14 12.7 6.55 0.11
6205 6205-Z 6205-2Z 6205-RS 6205-2RS 25 52 15 14 7.8 0.133
6206 6206-Z 6206-2Z 6206-RS 6206-2RS 30 62 16 19.3 11.2 0.201
6207 6207-Z 6207-2Z 6207-RS 6207-2RS 35 72 17 25.5 15.3 0.299
6208 6208-Z 6208-2Z 6208-RS 6208-2RS 40 80 18 29 18 0.382
6209 6209-Z 6209-2Z 6209-RS 6209-2RS 45 85 19 31 20.4 0.407
6210 6210-Z 6210-2Z 6210-RS 6210-2RS 50 90 20 36.5 24 0.478
6211 6211-Z 6211-2Z 6211-RS 6211-2RS 55 100 21 43 29 0.632
6212 6212-Z 6212-2Z 6212-RS 6212-2RS 60 110 22 52 36 0.807
6213 6213-Z 6213-2Z 6213-RS 6213-2RS 65 120 23 60 41.5 1.03
6214 6214-Z 6214-2Z 6214-RS 6214-2RS 70 125 24 62 44 1.11
6215 6215-Z 6215-2Z 6215-RS 6215-2RS 75 130 25 66 49.5 1.7
6216 6216-Z 6216-2Z 6216-RS 6216-2RS 80 140 28 72.5 53 2.1
6217 6217-Z 6217-2Z 6217-RS 6217-2RS 85 150 28 84 62 2.1
6218   6218-2Z   6218-2RS 90 160 30 96.5 72 2.26
6219   6219-2Z   6219-2RS 95 170 32 108 81.5 2.79
6220   6220-2Z   6220-2RS 100 180 34 122 93 3.36
6221   6221-2Z   6221-2RS 105 190 36 133 105 3.99
6300 6300-Z 6300-2Z 6300-RS 6300-2RS 10 35 11 8.15 3.45 0.057
6301 6301-Z 6301-2Z 6301-RS 6301-2RS 12 37 12 9.65 4.15 0.064
6302 6302-Z 6302-2Z 6302-RS 6302-2RS 15 42 13 11.4 5.4 0.09
6303 6303-Z 6303-2Z 6303-RS 6303-2RS 17 47 14 13.4 6.55 0.117
6304 6304-Z 6304-2Z 6304-RS 6304-2RS 20 52 15 15.8 7.8 0.155
6305 6305-Z 6305-2Z 6305-RS 6305-2RS 25 62 17 22.4 11.4 0.24
6306 6306-Z 6306-2Z 6306-RS 6306-2RS 30 72 19 26.5 16.3 0.363
6307 6307-Z 6307-2Z 6307-RS 6307-2RS 35 80 21 33.5 19 0.481
6308 6308-Z 6308-2Z 6308-RS 6308-2RS 40 90 23 42.5 25 0.654
6309 6309-Z 6309-2Z 6309-RS 6309-2RS 45 100 25 53 31.5 0.869
6310 6310-Z 6310-2Z 6310-RS 6310-2RS 50 110 27 61.8 38 1.12
6311 6311-Z 6311-2Z 6311-RS 6311-2RS 55 120 29 71.5 47.5 1.43
6312 6312-Z 6312-2Z 6312-RS 6312-2RS 60 130 31 82 52 1.79
6313 6313-Z 6313-2Z 6313-RS 6313-2RS 65 140 33 92.5 59.5 2.08
6314 6314-Z 6314-2Z 6314-RS 6314-2RS 70 150 35 104 68 2.52
6315 6315-Z 6315-2Z 6315-RS 6315-2RS 75 160 37 113 77 3.02
6316 6316-Z 6316-2Z 6316-RS 6316-2RS 80 170 39 123 86.5 3.59

 

How to Identify a Faulty Drive Shaft

The most common problems associated with automotive driveshafts include clicking and rubbing noises. While driving, the noise from the driver’s seat is often noticeable. An experienced auto mechanic can easily identify whether the sound is coming from both sides or from 1 side. If you notice any of these signs, it’s time to send your car in for a proper diagnosis. Here’s a guide to determining if your car’s driveshaft is faulty:
air-compressor

Symptoms of Driveshaft Failure

If you’re having trouble turning your car, it’s time to check your vehicle’s driveshaft. A bad driveshaft can limit the overall control of your car, and you should fix it as soon as possible to avoid further problems. Other symptoms of a propshaft failure include strange noises from under the vehicle and difficulty shifting gears. Squeaking from under the vehicle is another sign of a faulty driveshaft.
If your driveshaft fails, your car will stop. Although the engine will still run, the wheels will not turn. You may hear strange noises from under the vehicle, but this is a rare symptom of a propshaft failure. However, you will have plenty of time to fix the problem. If you don’t hear any noise, the problem is not affecting your vehicle’s ability to move.
The most obvious signs of a driveshaft failure are dull sounds, squeaks or vibrations. If the drive shaft is unbalanced, it is likely to damage the transmission. It will require a trailer to remove it from your vehicle. Apart from that, it can also affect your car’s performance and require repairs. So if you hear these signs in your car, be sure to have it checked by a mechanic right away.

Drive shaft assembly

When designing a propshaft, the design should be based on the torque required to drive the vehicle. When this torque is too high, it can cause irreversible failure of the drive shaft. Therefore, a good drive shaft design should have a long service life. Here are some tips to help you design a good driveshaft. Some of the main components of the driveshaft are listed below.
Snap Ring: The snap ring is a removable part that secures the bearing cup assembly in the yoke cross hole. It also has a groove for locating the snap ring. Spline: A spline is a patented tubular machined element with a series of ridges that fit into the grooves of the mating piece. The bearing cup assembly consists of a shaft and end fittings.
U-joint: U-joint is required due to the angular displacement between the T-shaped housing and the pinion. This angle is especially large in raised 4x4s. The design of the U-joint must guarantee a constant rotational speed. Proper driveshaft design must account for the difference in angular velocity between the shafts. The T-bracket and output shaft are attached to the bearing caps at both ends.
air-compressor

U-joint

Your vehicle has a set of U-joints on the driveshaft. If your vehicle needs to be replaced, you can do it yourself. You will need a hammer, ratchet and socket. In order to remove the U-joint, you must first remove the bearing cup. In some cases you will need to use a hammer to remove the bearing cup, you should be careful as you don’t want to damage the drive shaft. If you cannot remove the bearing cup, you can also use a vise to press it out.
There are 2 types of U-joints. One is held by a yoke and the other is held by a c-clamp. A full ring is safer and ideal for vehicles that are often used off-road. In some cases, a full circle can be used to repair a c-clamp u-joint.
In addition to excessive torque, extreme loads and improper lubrication are common causes of U-joint failure. The U-joint on the driveshaft can also be damaged if the engine is modified. If you are driving a vehicle with a heavily modified engine, it is not enough to replace the OE U-joint. In this case, it is important to take the time to properly lubricate these components as needed to keep them functional.

tube yoke

QU40866 Tube Yoke is a common replacement for damaged or damaged driveshaft tubes. They are desirably made of a metallic material, such as an aluminum alloy, and include a hollow portion with a lug structure at 1 end. Tube yokes can be manufactured using a variety of methods, including casting and forging. A common method involves drawing solid elements and machining them into the final shape. The resulting components are less expensive to produce, especially when compared to other forms.
The tube fork has a connection point to the driveshaft tube. The lug structure provides attachment points for the gimbal. Typically, the driveshaft tube is 5 inches in diameter and the lug structure is 4 inches in diameter. The lug structure also serves as a mounting point for the drive shaft. Once installed, Tube Yoke is easy to maintain. There are 2 types of lug structures: 1 is forged tube yoke and the other is welded.
Heavy-duty series drive shafts use bearing plates to secure the yoke to the U-joint. All other dimensions are secured with external snap rings. Yokes are usually machined to accept U-bolts. For some applications, grease fittings are used. This attachment is more suitable for off-road vehicles and performance vehicles.
air-compressor

end yoke

The end yoke of the drive shaft is an integral part of the drive train. Choosing a high-quality end yoke will help ensure long-term operation and prevent premature failure. Pat’s Driveline offers a complete line of automotive end yokes for power take-offs, differentials and auxiliary equipment. They can also measure your existing parts and provide you with high quality replacements.
A U-bolt is an industrial fastener with threaded legs. When used on a driveshaft, it provides greater stability in unstable terrain. You can purchase a U-bolt kit to secure the pinion carrier to the drive shaft. U-bolts also come with lock washers and nuts. Performance cars and off-road vehicles often use this type of attachment. But before you install it, you have to make sure the yoke is machined to accept it.
End yokes can be made of aluminum or steel and are designed to provide strength. It also offers special bolt styles for various applications. CZPT’s drivetrain is also stocked with a full line of automotive flange yokes. The company also produces custom flanged yokes for many popular brands. Since the company has a comprehensive line of replacement flange yokes, it can help you transform your drivetrain from non-serviceable to serviceable.

bushing

The first step in repairing or replacing an automotive driveshaft is to replace worn or damaged bushings. These bushings are located inside the drive shaft to provide a smooth, safe ride. The shaft rotates in a rubber sleeve. If a bushing needs to be replaced, you should first check the manual for recommendations. Some of these components may also need to be replaced, such as the clutch or swingarm.

China manufacturer Timken, Skfbearing, NSK, NTN, CZPT Bearing, Kbc CZPT Bearing, Auto/ Agricultural Machinery Ball Bearing 6001 6002 6003 6004 6201 6202 6203 6204zz 2RS C3     with high qualityChina manufacturer Timken, Skfbearing, NSK, NTN, CZPT Bearing, Kbc CZPT Bearing, Auto/ Agricultural Machinery Ball Bearing 6001 6002 6003 6004 6201 6202 6203 6204zz 2RS C3     with high quality